基于电机效率的纯电动汽车传动系统参数匹配研究

为降低能耗、提高续航里程,本文提出了以提高电机效率为目标的纯电动汽车三档变速传动方案.首先,在分析电机工作特性的基础上提出了三档传动系统参数匹配方法;然后以某纯电动汽车为研究对象,对其驱动系统进行了改动:方案一在不改变原车型动力系统参数的情况下将传动系统由一档改为三档,并运用所提出的方法确定各档位的传动比;方案二在满足整车动力性指标要求下对电机重新选型并匹配三档传动系统;最后利用ADVISOR软件进行NEDC工况仿真分析.结果表明:在不改变原车型动力系统参数的情况下,采用三档传动可使整车的动力性和经济性都有一定的提升,续航里程提高了 9.2％,百公里电耗降低了 1.28 kW·h;重新选型电机后,采用三档传动续航里程提高了 14.1％,百公里电耗降低了 1.87kW·h.     

One step method of structure engineering porous graphitic carbon nitride for efficient visible-light photocatalytic reduction of Cr(Ⅵ)

Porous g-C3N4 nanosheets (PCN) were prepared by the nickel-assisted one-step thermal polymerization method.Hydrogen (H2) which was produced by the reaction between nickel (Ni) foam and ammonia (NH3) defined the structure and properties of PCN.During the formation of PCN,the participation of H2 not only enhanced the spacing between layers but also boosted the specific surface area that more active sites were exposed.Additionally,H2 promoted pores formation in the nanosheets,which was beneficial to the transfer of photons through lamellar structure and improved the absorption efficiency of visible light.Remarkably,the obtained PCN possessed better Cr(Ⅵ) photocatalytic reduction efficiency than pure g-C3N4.The reaction rate constant (k) of PCN (0.013 min-1) was approximately twice that of bare g-C3N4 (0.007 min-1).Furthermore,the effects of original pH and concentration of Cr(Ⅵ)-containing solution on removal efficiency of Cr(Ⅵ) were explored.A possible photocatalytic mechanism was proposed based on the experiments of radical scavengers and photoelectrochemical characterizations.     

坛紫菜蛋白质提取工艺优化及其特性分析

为了开展坛紫菜高值化加工利用，以坛紫菜为原料、蛋白质提取率为评价指标，通过考察提取溶剂、超声时间和功率、料液比、pH等单因素实验、正交试验设计优化超声波提取工艺，对其等电点、乳化性、起泡性等基础特性进行分析，并进行抗氧化活性测定。结果表明，在超声全程时间50 min、超声功率1350 W条件下，坛紫菜蛋白质提取率为60.98%±1.01%。同时通过对所提取的坛紫菜蛋白质特性分析结果显示，坛紫菜蛋白质的等电点为4.5，在等电点附近，坛紫菜蛋白质有较好的泡沫稳定性，可达80.84%±2.95%；抗氧化测定结果显示，坛紫菜蛋白质在5~50 mg/mL范围内具有较强的抗氧化活性，浓度为50 mg/mL时，总抗氧化能力为2.89±0.09 U/mL，ABTS+自由基清除能力相当于0.83±0.08 mmol/L Trolox，DPPH清除率在10 mg/mL时达到68.04%±0.73%。该研究可以为坛紫菜资源的开发利用提供一定的理论依据和技术支持。     

柿竹园多金属矿选矿废水处理试验研究

针对柿竹园多金属矿选矿废水量大、难沉降、pH值高、COD高等特点,研究了石灰沉降+ZJYH03氧化法、石灰沉降+漂白粉氧化法、石灰沉降+NaClO氧化法、聚合硫酸铁沉降+ZJYH03氧化法和石灰沉降+生物氧化法等废水处理工艺,并对比分析了各工艺的处理效果和药剂成本,结果表明: 聚合硫酸铁沉降+ZJYH03氧化法取得了较好的处理效果,该方法具有工艺简单、水质无色透明、药剂成本低等特点。     

Generating Questions Based on Semi-Automated and End-to-End Neural Network

With the emergence of large-scale knowledge base, how to use triple information to generate natural questions is a key technology in question answering systems. The traditional way of generating questions require a lot of manual intervention and produce lots of noise. To solve these problems, we propose a joint model based on semi-automated model and End-to-End neural network to automatically generate questions. The semi-automated model can generate question templates and real questions combining the knowledge base and center graph. The End-to-End neural network directly sends the knowledge base and real questions to BiLSTM network. Meanwhile, the attention mechanism is utilized in the decoding layer, which makes the triples and generated questions more relevant. Finally, the experimental results on SimpleQuestions demonstrate the effectiveness of the proposed approach.     

白炭黑或埃洛石填充不同橡胶树品系天然橡胶复合材料的性能研究

分别采用白炭黑或埃洛石填充4种橡胶树品系（72059，PR107,73397和RRIM600）天然橡胶（NR）以制备复合材料，并研究复合材料的各项性能。结果表明：白炭黑或埃洛石填充NR复合材料的硫化特性受橡胶树品系的影响较小；两种填料填充的RRIM600复合材料均表现出最大的溶胀平衡交联密度和最优的物理性能，且50～70 ℃范围内的损耗因子最小，表明RRIM600复合材料的滞后损失最小，RRIM600满足低滚动阻力轮胎的用胶要求，而72059复合材料的相应性能较差；白炭黑填充72059复合材料的热稳定性最优，埃洛石填充各橡胶树品系NR复合材料的热稳定性差异不明显；PR107复合材料和73397复合材料的综合性能居中。     

Experimental investigation of different morphology textured ceramic tools by in-situ formed for the dry cutting

Surface texture is considered an important measure to improve the cutting performance of a tool. In this study, we have prepared three types of textured and conventional tools on the rake face by an in-situ formed method. During the experiment, the best parameters of three types of textured tools were selected for dry cutting AISI 1045 steel at different cutting speeds. Cutting forces, cutting temperatures, workpiece surface roughness, and tool wear were measured during the cutting process. The results showed that textured tools have significantly reduced cutting force, cutting temperature, and tool wear, and the roughness of the workpiece was improved compared with the conventional tool. The micro-pit texture tool has less stress contact region than the micro-groove width texture tool, but the micro-groove width texture tool exhibiting the best cutting performance. This investigation clearly showed that the textured tool prepared by the in-situ formed method has improved cutting performance.